Measuring Tianwen-1’s modulation

This is a post I had announced since I first described Tianwen-1’s modulation. Since we have very high SNR recordings of the Tianwen-1 low rate rate telemetry signal made with the 20m dish in Bochum observatory, it is interesting to make detailed measurements of the modulation parameters. In fact, there is something curious about the way the modulation is implemented in the spacecraft’s transmitter. This analysis will show it clearly, but I will reserve the details for later in the post.

Here I will be using a recording that already appeared in a previous post. It was made on 2020-07-26 07:47:20 UTC in Bochum shortly after the switch to the high gain antenna, so the SNR is fantastic. The recording was done at 2.5Msps, and the spectrum can be seen below. The asymmetry (especially around +1MHz) might be due to the receive chain.

The signal is residual carrier phase modulation, with 16348 baud BPSK data on a 65536Hz square wave subcarrier. There is also a 500kHz ranging tone.

Tianwen-1 attitude during cruise and early orbit

In a previous post I talked about the ADCS telemetry of Tianwen-1. In there I showed that Space Packets in APID 1281 had several fields corresponding to the ADCS, including the quaternion giving the spacecraft attitude. I used these quaternions to show that the spacecraft had made a turn of 15º about its Y axis. However, at that time I still lacked some details to give a full interpretation of the attitude quaternions, such as what frame of reference they used or how were the spacecraft body axes defined.

Now I have looked at all the telemetry we have collected so far and with this I’ve been able to guess the missing details, so I can give a complete interpretation of the attitude quaternions. In this post I will show the attitude control law of Tianwen-1 on its cruise orbit to Mars and also the attitude during early orbit operations.

Decoding Mars 2020

Mars 2020, NASA’s latest mission to Mars, was launched a couple weeks ago. However, with all the Tianwen-1 work down the pipeline, until now I haven’t had time to dedicate an appropriate post to this mission (though I showed some sneak peek on Twitter). This mission consists of a rover and helicopter (a real novelty in space exploration). Both were launched with the cruise stage and the entry, descent and landing system on July 30 from Cape Canaveral, an are currently on their transfer orbit to Mars, as Tianwen-1 and Emirates Mars Mission.

In this post I will be working with some recordings made by AMSAT-DL using the 20m radio telescope at Bochum’s observatory. These feature the low rate safe mode telemetry, which was very strong and caused some anecdotes as it saturated some NASA DSN receivers, and the nominal 10kbps telemetry signal that was switched on later. Here I will describe the modulation and coding, giving GNU Radio decoders, and also take a look at the data. r00t.cz has also written a post where he shows similar information.

Tianwen-1 virtual channel 24

In this post I analyse part of the telemetry transmitted by Tianwen-1 over high-speed data done on 2020-08-03. The decoded frames were kindly provided by Paul Marsh M0EYT. r00t.cz has made an analysis of this data in his Tianwen-1 page, which also includes some more information not shown here. This telemetry contains a full playback of some channels spanning 2020-07-25 to 2020-08-02, including gyroscope data, as described in this post.

Tianwen-1 high speed data signal

In a previous post I talked about how the high data rate signal of Tianwen-1 can be used to replay recorded telemetry. I did an analysis of the telemetry transmitted over the high speed data signal on 2020-07-30 and showed how to interpret the ADCS data, but left the detailed description of the modulation and coding for a future post.

Here I will talk about the modulation and coding, and how the signal switches from the ordinary low rate telemetry to the high speed signal. I also give GNU Radio decoder flowgraphs, tianwen1_hsd.grc, which works with the 8192 bit frames, and tianwen1_hsd_shortframes.grc, which works with the 2048 bit short frames.

Tianwen-1 post–TCM-1 state vectors

Yesterday I reported about Tianwen-1’s first trajectory correction manoeuvre, TCM-1. In that post I commented the possibility that the updated state vectors that we saw on the telemetry after TCM-1 might come from a prediction or planning rather than take into account the actual performance of the burn.

The figure below shows the error between the state vectors collected after TCM-1 over the last two days, and a trajectory propagated in GMAT, using the following state vector, which is one of the first received after TCM-1.

[0151059eb9ea] 2020-08-02 00:17:06.711400 100230220.21360767 -106145016.11787066 -45441035.07405791 25.581827920522485 18.240707152437626 8.567874276424218

We see that on the UTC night between August 1 and 2 the state vectors deviate very little from the GMAT trajectory. However, on the UTC night between August 2 and 3 we see a slightly different trajectory in the state vectors. We have no data in between, as the spacecraft is not visible in Europe, so we don’t know the precise moment of change. The gap in telemetry around 2020-08-03 00:45 UTC is due to a transmission of high-speed data.

It seems reasonable to think that after TCM-1 the Chinese DSN performed precise ranging of the spacecraft to determine the new orbit accurately and then uploaded a correction to the state vectors on-board Tianwen-1.

The state vectors from last night all describe the same trajectory, as shown in the plot below which uses

[0151322e67d0] 2020-08-02 21:03:08.078400 102132184.96868199 -104770375.00352533 -44795830.46284772 25.29849580646669 18.532513218789806 8.692135086385246

to propagate a trajectory in GMAT. There is a small jump of a few hundred meters at some point. We usually see one or two these jumps per day, but we don’t understand well why they happen.

The trajectory according to the state vectors from 00:17:06 and from 21:03:08 are very similar. For example, at the closest approach to Mars they only differ in 1197km. For comparison, the difference between the new trajectory and the pre–TCM-1 trajectory is 126529km (again, at the closest approach to Mars).

I have generated a new table of right-ascension, declination and distance coordinates based on the updated state vectors. Note that this table doesn’t include light-time delay to the spacecraft.

Thanks to AMSAT-DL‘s Bochum observatory team and to Paul Marsh M0EYT for their continuous effort in tracking Tianwen-1. The data used in this post has come from their observations.

Tianwen-1 TCM-1

On 2020-08-01 23:00 UTC, Tianwen-1 made its first correction manoeuvre, called TCM-1. The manoeuvre was observed by Amateur trackers, such as Edgar Kaiser DF2MZ, Paul Marsh M0EYT, and the 20m antenna at Bochum observatory, operated by AMSAT-DL. The news of the successful manoeuvre appeared in Chinese media, and in the German Wikipedia article for Tianwen-1 (thanks to Achim Vollhardt DH2VA for sharing this information).

Since Tianwen-1 transmits its own real time orbit state vectors in the telemetry, by comparing the vectors transmitted before and after TCM-1, and also by studying the Doppler observed by groundstations on Earth, we can learn more about the manoeuvre.

Tianwen-1 manoeuvre and high-speed data

On the Beijing time morning of 2020-07-30, Tianwen-1 did something. Paul Marsh M0EYT reports that the probe first switched from the high gain antenna to the low gain antenna, then returned to the high gain antenna, and then switched to a high-speed data mode, finally coming back to the usual 16384baud telemetry.

r00t.cz has already analysed the telemetry data collected during this event. He reports that the high speed data was a replay of the telemetry produced during the period when the low gain antenna was used. He shows some interesting behaviour on APIDs 1280, 1281 and 1282 (see my previous post for a description of these during nominal operation). These seem to contain ADCS data.

This event was followed with some expectation by the Amateur deep space tracking community, since according to this paper Tianwen-1 would make the first correction manoeuvre (TCM-1) early on in the mission (day 9 is stated in the paper). However, by now it is clear that a true correction manoeuvre didn’t happen, since no significant change has been seen in the trajectory described by the state vectors transmitted in the spacecraft’s telemetry. However, this event might have been a very small thruster firing, in order to test the propulsion in preparation for the true TCM-1.

In this post, I look at the data during the high speed replay, following the same approach as in the previous post. With this data, I reach a definite conclusion of what happened during this event (I won’t spoil the mystery by stating it in advance). The description of the modulation and coding used by the high speed data will come in a later post.

The Jupyter notebook for the calculations in this post can be found here.

Tianwen-1 telemetry: framing and data

This is a follow-up to my previous post, where I explained the modulation and coding of Tianwen-1’s telemetry. In this post I will explain the framing structures and the data contained in the telemetry (though we only understand a few of the telemetry channels). Most of what I’m going to explain here was found first by r00t.cz and is already presented in his Tianwen-1 page. In this post I’ll try to give a bit more detail (especially for those not so familiar with the CCSDS protocols) and some Python code for those interested in digging into the data.